3dm683D 3 Phase Hybrid Stepping Motor Driver
|1-9 10-49 50-99 100+|
|FOB Unit Price:||US $30 US $28.5 US $27.5 US $26|
|Purchase Qty. (Pieces)||FOB Unit Price|
|Payment Terms:||L/C, T/T, Paypal, Western Union|
- Model NO.: 3DM683D
- Number of Stator: Three-Phase
- Function: Driving
- Certification: ISO9001, CE
- Voltage Range: 24-60VDC
- Dimension: 118mm*75mm*32mm
- Suitable Stepper Motor: NEMA 23/34 3 Phase Stepper Motor
- Specification: CE
- HS Code: 850300
- Speed: Variable Speed
- Excitation Mode: HB-Hybrid
- Number of Poles: 3
- Current Range: 3.2-8.3A
- Subdivision: 800-51200PPS
- Weight: 0.3kg
- Control Mode: Differential
- Origin: Changzhou Jiangsu
The 3DM683 is a new generation high-performance digital stepper driver based on DSP with advanced control algorithm. The motors driven by 3DM683 can run with much smaller noise and much less vibration than other drivers in the market. The 3DM683 possess the feature of lower noise, lower vibration, and lower heating. The 3DM683's voltage is DC 24V-60V. It is suitable for all the 3-phase hybrid stepper motor whose current is less than 5.6A.There are 16 kinds of microstep of 3DM683. The maximum step number of 3DM683 is 51200 steps/rev (microstep is 1/256 ). Its current range is 3.2A-8.3A, and its output current has 8 stalls. 3DM683 has automatic semi-flow, over-voltage, under voltage and over-current protection function.
The red indicator is on.
|1. A short circuit of motor wires.||Inspect or change wires|
|2. The external voltage is over or low than the driver's working voltage.||Adjust the voltage to a reasonable rang|
|3. Unknown reason||Return the goods|
It can be applied in a variety of small scale automation equipment and instruments, such as labeling machine, cutting machine, packing machine, drawing machine, engraving machine, CNC machine and so on. It always performs well when it is used in equipment which requires for low-vibration, low-noise, high-precision and high-velocity.
Driver functions descriptions
|Driver function||Operating instructions|
|Users can set the driver output current by SW1-SW3 three switches.|
The setting of the specific output current, please refer to the instructions of the driver panel figure.
|Users can set the driver Microstep by the SW5-SW8 four switches. The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure.|
|Users can set the driver half flow function by SW4. "OFF" indicates the quiescent current is set to half of the dynamic current, that is to say, 0.5 seconds after the cessation of the pulse, current reduce to about half automatically. "ON" indicates the quiescent current and the dynamic current are the same. User can set SW4 to "OFF", in order to reduce motor and driver heating and improve reliability.|
|PUL+ and PUL- are the positive and negative side of control pulse signal; DIR+ and DIR- are the positive and negative side of direction signal; ENA+ and ENA- are the positive and negative side of enable signal.|
|A+ and A- are connected to a phase winding of motor; B+ and B- are connected to another phase winding of motor. If you need to backward, one of the phase windings can be reversed.|
|It uses DC power supply. Recommended operating voltage is 24VDC-60VDC, and power consumption should be greater than 100W.|
|There are two indicator lights. Power indicator is green. When the driver power on, the green light will always be lit. Fault indicator is red, when there is over-voltage or over-current fault, the red light will always be lit; after the driver fault is cleared, if re-power the red light will be off.|
|Driver dimensions:118×75×32mm, please refer to dimensions diagram. Please leave 10CM space for heat dissipation. During installation, it should be close to the metal cabinet for heat dissipation.|
Signal interface details:
The internal interface circuits of the driver are isolated by the opt coupler signals, R in the figure is an external current limiting resistor. The connection is differential. And it has a good anti-jamming performance.
Control signal and external interface:
External current limiting resistor R
The red indicator is on.
1. A short circuit of motor wires.
Inspect or change wires
2. The external voltage is over or low than the driver's working voltage.
Adjust the voltage to a reasonable rang
3. Unknown reason
Return the goods
Changzhou Jinsanshi Mechatonics Co.,Ltd
Contact Person : Christal
More Quantity . More Discount !!!